ESP8266 DHT11 Temperature and Humidity WiFi Module Wireless Module ESP-01 01S

Description

ESP8266 DHT11 Temperature and Humidity WiFi Module Wireless Module ESP-01 01S
Description:
ESP8266 ESP-01/01S DHT11 Temperature&Humidity Wifi Shield
Master: ESP-01 / ESP-01S (this module does not include ESP-01 / ESP-01S)
Temperature and humidity sensor: DHT11
Operating voltage: DC 3.7 V-12 V (support 3.7 v lithium battery power supply)
Measuring range: 20-90% RH 0-50 ° C
Measurement accuracy: Temperature: ± 2 ° Humidity ± 5% RELATIVE HUMIDITY
Application example:
1. Power source: 3.7 V-12 V DC power supply connected to VCC GND (2.54mm pin)
2. Download the program to ESP-01S
3. Insert ESP-01 / ESP-01S into the 2 * 4 Pin
Package includes:
1 * ESP8266 ESP-01 ESP-01S ESP01 DHT11 Temperature and Humidity Sensor module NodeMCU
ESP8266 Wifi Smart Home IOT For Arduino DIY Kit
ESP8266 Esp-01 Serial Port WIFI Transceiver Wireless Module
ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete
and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi
networking functions from another application processor.
ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the
sensors and other application specific devices through its GPIOs with minimal development up-front and
minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry,
and the entire solution, including front-end module, is designed to occupy minimal PCB area.
Features
SDIO 2.0, SPI, UART
32-pin QFN package
Integrated RF switch, balun, 24dBm PA, DCXO, and PMU
Integrated RISC processor, on-chip memory and external memory interfaces
Integrated MAC/baseband processors
Quality of Service management
I2S interface for high fidelity audio applications
On-chip low-dropout linear regulators for all internal supplies
Proprietary spurious-free clock generation architecture
Integrated WEP, TKIP, AES, and WAPI engines
Solutions
Supports APSD for optimal VoIP applications
Patented spurious noise cancellation algorithm for integration in SOC applications
Supports Bluetooth co-existence interface
Self-calibrated RF to ensure optimal performance under all operating conditions
Zero factory tuning
No external RF components
Specifications
802.11 b/g/n
Wi-Fi Direct (P2P), soft-AP
Integrated TCP/IP protocol stack
Integrated TR switch, balun, LNA, power amplifier and matching network
Integrated PLLs, regulators, DCXO and power management units
+19.5dBm output power in 802.11b mode
Power down leakage current of <10uA
Integrated low power 32-bit CPU could be used as application processor
SDIO 1.1/2.0, SPI, UART
STBC, 1×1 MIMO, 2×1 MIMO
A-MPDU & A-MSDU aggregation & 0.4ms guard interval
Wake up and transmit packets in < 2ms
Standby power consumption of < 1.0mW (DTIM3)
Help your development more easy.
ESP8266 Serial WIFI Module Communite Forum>>Detail about ESP8266
1. High quality & low price
2. LWIP agreement
3. Support 3 modes: AP, STA, AP+STA
4. Perfect and simple AT commands
>>>>Translate data sheet
>>>>Some translated document
>>>>Turial
Now your Arduino can get on WiFI without braking the bank.
Use this module for your next Interet of Things project, home automation, Or remote sensor project.
This module adats the ESP8226 IC for use over a serial connection using simple AT commands.
No SPI interface or Know-How is required.
Warnings:
This module requires a 3.3 volt supply for VCC, and 3.3V logic. It is not 5V tolant. Connect RX or TX on 5V Arduino will
destroy this module. You must use a logic level converter, or a 3.3V Arduino
The 3.3V supply on the Arduino Uno has inadequate current capabilit to power this module. You must provide a separate,
higher 3.3V supply(about 300mA or better)
The ESP8225 module is very new on the market and support and documentation for it is currently very limited.
Package Included:
1 x ESP8266 Serial WIFI Wireless Transceiver Module Send Receive LWIP AP+STA
Payment
Returns
Shipping
Payment
We only accept payment through Paypal.
Items will go to post within 1-2 business days after payment confirmed.
Returns
If you can't receive the product within 2 months (60 days), please contact with us,we promise to payback 100% of your money.
We ensure our products work normally before post.If the products is broken before arrival to you,all you should do is taking a photo to show us our broken product.We promise to payback 100% of your money.
Shipping
1. We ship to Worldwide.
2. We only ship to confirmed PAYPAL address; your PAYPAL address must match your Shipping address.
3. Any non-received items caused by invalid address registered on PayPal are not in our full refund or replacement policy. Shipping fee has including the local handing and packaging fee.
4. All the items will be shipping within 1-2 working days after receiving the payment, except some holidays.
5. We will not be responsible for any custom delay or tax, because transit time is highly depended and provided by postal Service.
6. If you have any problem, please contact us via message, we will reply message within 1-2 working days, please wait for patient.