I2C GY-213V HTU21D/SHT21/SI7021/HDC1080/SHT20 Temperature&Humidity Sensor

Description

Visit store
Items for sale
About us
Product Details
Description：
(This 5 item have the same appearance but diffrent chips)
HTU21D
The main chip of this item is GY-213V-HTU21D
The HTU21D is a low-cost, easy to use, highly accurate, digital humidity and temperature sensor.
This sensor is ideal for environmental sensing and data logging and perfect for a weather stations or
humidor control systems. All you need is two lines for I2C communication and
you’ll have relative humidity readings and very accurate temperature readings as a bonus!
There are only four pins that need to be hooked up in order to startusing this sensor in a project.
One for VCC, one for GND, and two data lines for I2C communication. This breakout board has built in 4.7k
pull up resistors for I2C communications.If you’re hooking up multiple I2C devices on the same bus,
you may want to disable these resistors.Dimensions: 0.6 x 0.6"Documents
Schematic
Eagle Files
Datasheet(HTU21D)
Hookup Guide
HTU21D Library
GitHub
Package Included:1 XI2C GY-213V-HTU21D Temperature&Humidity Sensor
SHT21
The main chip is GY-213V-SHT21(Can be replace by HTU21D SI7021 HDC1080)
The Humidity and Temperature Sensor is an Arduino-compatible sensor board that carries an SHT21 digital humidity and temperature sensor from Sensirion. It has a 4-pin interface that can communicate directly with the analog pins on the Arduino.The SHT21 utilizes a capacitive sensor element to measure humidity, while the temperature is measured by a band gap sensor. Both sensors are seamlessly coupled to a 14-bit ADC, which then transmits digital data to the Arduino over the I2C protocol. Because of the sensor’s tiny size, it has incredibly low power consumption, making it suited for virtually any application.
To optimize accuracy of temperature and humidity readings, the SHT21 sensor is placed at the tip of the board, isolating it from heat producing circuitry. Two of the sensor’s four pins are ground and +5V; the other two are clock and data pins that make up the 2-wire serial interface. The board is 5V tolerant and designed to operate directly off the supply voltage coming from the Arduino.
The sensor can be placed in soil to measure moisture and temperature, which makes it ideal for using it in a garden or greenhouse. The humidity sensor is also especially useful in building remote weather stations.
* Energy consumption: 80 uW (at 12 bit, 3V, 1 measurement/s)
* Relative Humidity operating range: 0-100% RH
* Relative Humidity resolution of 0.03%
* Relative Humidity Response Time of 8 sec (tau 63%)
* Temperature operating range: -40 to +125°C
* Temperature resolution of 0.01 C
* 4 pins: +5V, GND, Clock (SCL), Data (SDA)
* Bidirectional communication over a single pin on I2C protocol
* Board is 5V tolerant, allowing sensor to run from a 5V supply on Arduino I/O pins
Applications:
* Homes, basements and HVAC systems for measuring humidity
* People with physical conditions sensitive to humidity
* Home ventilating, heating and air conditioning systems
* Meteorology stations to predict or check weather temperatures
* Gardens or greenhouses to check humidity and temperatures
Resources
* SHT21 sensor Datasheet
* LibHumidity Arduino library
Package Included:1 x Low Power I2C GY-213V-SHT21 High Accuracy Digital Humidity&Temperature Sensor
HDC1080
The main chip is GY-213V-HDC1080(Can use SHT21 HTU21D SI7021 chip to made the same sensor)
This I2C digital humidity sensor is a fairly accurate and intelligent alternative to the much simpler Humidity and Temperature Sensor - SHT15 Breakout It has a typical accuracy of ±4% with an operating range that's optimized from 10% to 80% RH. Operation outside this range is still possible - just the accuracy might drop a bit. The temperature output has a typical accuracy of ±0.2°C from -20~85°C.
The HDC1080 sensor chip has 2 address-select pins, so you can have up to 4 shared on a single I2C bus. It's also 3-5V power and logic safe so you don't need any level shifters or regulators to use with a 5V or 3V microcontroller.
Please note: TI has indicated that there's a 'settling' effect for the humidity and that you will need to re-hydrate the sensor once you receive it. To rehydrate it, place it in a location with 85% humidity for 24 hours or 60% humidity for 10 days.
The HDC1080 is a digital humidity sensor with integrated temperature sensor that provides excellent measurement accuracy at very low power. The HDC1080 operates over a wide supply range, and is a low cost, low power alternative to competitive solutions in a wide range of common applications. The humidity and temperature sensors are factory calibrated.
Features
Relative Humidity Accuracy ±2% (typical)
Temperature Accuracy ±0.2°C (typical)
Excellent Stability at High Humidity
14 Bit Measurement Resolution
100 nA Sleep Mode Current
Power Pins:
Vin - this is the power pin. Unlike many sensors, this chip can be powered by 3-5 VDC, so there is no voltage regulator on board. Simply power the board with the same power as the logic level of your microcontroller - e.g. for a 5V micro like Arduino, use 5V. For a 3V ARM processor, use 3V
GND - common ground for power and logic
I2C Logic pins:
SCL - I2C clock pin, connect to your microcontrollers I2C clock line. 3-5V logic OK
SDA - I2C data pin, connect to your microcontrollers I2C data line. 3-5V logic OK
Optional Pins
These are pins you don't need to connect to unless you want to!
RDY - This is the interrupt/'ready' pin from the HDC100x. The chip has some capability to 'alert' you when data is ready to be read from the sensor. We don't use this pin in our library but it's available if you need it! It is open collector so you need to use a pull-up resistor if you want to read signal from this pin.
A0 A1 - These are the address select pins. Since you can only have one device with a given address on an i2c bus, there must be a way to adjust the address if you want to put more than one HDC100X on a shared i2c bus. The A0/A1 pins set the bottom 2 bits of the i2c address. There are pull-down resistors on the board so connect them to Vin to set the bits to '1'. They are read on power up, so de-power and re-power to reset the address
Package Included:1 X Low Power I2C GY-213V-HDC1080 High Accuracy Digital Humidity&Temperature Sensor
Si7021
Precision Relative Humidity Sensor
± 3% RH (max), 0–80% RH
High Accuracy Temperature Sensor
±0.4 °C (max), –10 to 85 °C
0 to 100% RH operating range
Up to –40 to +125 °C operating range
Wide operating voltage (1.9 to 3.6 V)
Low Power Consumption 150 μA active current
60 nA standby current
Factory-calibrated
I2C Interface
Integrated on-chip heater
3x3 mm DFN Package
Excellent long term stability
Optional factory-installed cover
Low-profile
Protection during reflow
Excludes liquids and particulates
Applications:
HVAC/R
Thermostats/humidistats
Respiratory therapy
White goods
Indoor weather stations
Micro-environments/data centers
Automotive climate control and defogging
Asset and goods tracking
Mobile phones and tablets
Size: 1.3*1cm/0.51*0.39"
Package includes:1PCS Si7021 Industrial High Precision Humidity Sensor with I2C Interface NEW
SHT20
1. Supply voltage: 1.5V-3.6V
2. Humidity measuring range: 0-100%RH
3. Temperature range: -40 ℃-105℃
4. Maximum power consumption: 2.7uW communication: I2C
5. Humidity accuracy range:
6. 10% RH to 95% RH
7. Humidity Hysteresis: ±1% RH
8. Measurement time: 50ms
9. The annual shift: -0.5% RH / year
10. Response time: 5s
11. Accuracy:
12. HTU20D T: +/-0.3℃
13. RH: +/- 4% RH
14. HTU21D T: +/-0.3℃
15. RH: +/- 2% RH
16. Storage temperature: -40℃ ~ 125℃
17. Working humidity range: 0-100% RH
18. Working temperature range: -40℃ ~ 105℃
Package Included:1 X SHT20 Temperature Humidity Sensor
Payment Method
Shipping Policy
Returns & Refund Policy
Feedback
Payment Method
EBAY Managed Payment.
But we only
Accept
your
Ebay Address
, please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping Policy
1. We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.
2. Orders will be processed instantly and dispatched within 1-3 business days except hoilday, so we do NOT accept any email/message note after you place orders.
3. All package need to wait 30 days,Please take care it.Less than 30 days,we can't take a refund.
Returns & Refund Policy
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please keep in touch with us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Feedback
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.